Following are the most frequently asked questions of FgTech Galletto V54 ECU tuning kit Master version. About software: Q: I have got my package, but the CD is broken, where and how can i get the software? A: Sorry, you… Continue Reading
Kess V2 Vehicle List Download: http://www.eobdtool.co.uk/upload/pro/kess-v2-obd2-tuning-kit-vehicle-list.xls Attention: Pleas do not update Kess V2 China clone online. Notes: 1. Be sure that Anti-Virus software is disabled or closed Please be attention,anti-virus software will treat our KESS V2 OBD tuning software as… Continue Reading
Problem: When install FGTech Galletto 2, the FTReadWrite replied “Can’t find device” error message. When trying to uninstall the driver, the window screen warmed it is not FGTECH device, but USB-to-Serial device. If install the driver, fgtech software did not run and FTReadWrite or MProg didn’t find the ftdi chip. Try to install the driver on both win 7 and win xp computer over and over, but in vain. Solution: 1) Download and install the Virtual Com Port drivers from FTDI website: Virtual COM Port Drivers http://www.ftdichip.com/Drivers/VCP.htm 2) Then connect the FGTech to computer via USB port which had no device programmed and 1 blank device when the MProg Utility it shows. NOTE: If you had backup and reprogram with the ept file. The system will not recognize the FGTECH Galletto 2 and will not reprogram the firmware bin file. The Virtual Com Port Drivers would overlay the fgtech ECU programmer. Then you have to again download the related driver in FTDI website. CMD Uninstaller 1.4 http://www.ftdichip.com/Support/Utilities.htm 3) After install the right drivers, FTReadWrite programmed the backup firmware file, run FGTech software by referring to the user manual on obd365 webpage. www.eobdtool.co.uk here offers some FGTECH related files download.
I purchased: MINI VCI Toyota TIS Techstream cable the latest version V9.30.002 from obd365 for US$ 29.99 without shipping fee. How to use: For the MINI VCI software installation part, I followed by the tutorial video Mini Vci Toyota Techstream 9.30.002 installation video Then I referred the blog of how to run the mini vci cable on Windows 7 64 bit operating system What MINI VCI did: http://www.eobdtool.co.uk/wholesale/cheap-mini-vci-single-cable-for-toyota-26480.html –Remove the seat belt reminder –Reset my transmission adapted memory after a transmission rebuilt –Test and read live streaming data, e.g transmission temperature (down to 99.5) – reset steering angle sensor to get rid of annoying 10 degree off centered wheel. –Run vehicle health test –Reset ABS and airbag light –Turn off the wipe because delay 3s by using windshield washer –One push remote to turn on unlock door –Adjust interior light delays and headlight off. –Adjust Throttle position sensor For other functions I have not test yet and I could not comment on them. What are your experiences with MINI VCI cable?
I have an BMW INPA cable myself but used to install it on a XP laptop. Recently some forum members are asking is it possible to use it on Windows 7 system? If yes, how to? After much research, I have finally got it working and hope this can help any of you. I only used it on my E46 M3 (2004) and so I can confirm that it works fully with this car but I cannot guarantee if it works on other BMW cars. 1. Buy a cable I purchased my cable from Careucar. It came with software in a mini CD. This is the specific cable that I purchased and that I can confirm works: http://www.eobdtool.co.uk/wholesale/best-price-bmw-inpa-k-can-with-ft232rl-chip.html 2. Setup/Configure your OBD2 USB Cable Put the CD into your PC. Connect the cable into a USB port on your PC. The PC should automatically search USB cable drivers. Follow the prompts to install the driver. Once installed, go to Control Panel -> System -> click on the Hardware tab, and then click on Device Manager to make sure there is ‘USB Serial Port (COMX)’. Right-click on the above and select ‘Properties’, then click on the ‘Port Settings’ Tab and then click on ‘Advanced’. Change the ‘Com Port Number’ entry to ‘COM1′. Change the ‘Latency Timer (msec)’ to ’1′. Click on ‘OK’ and close all the windows, restart your PC to confirm all the changes. 3. Install INPA/EDIABAS software Extract the contents of the downloaded file ‘INPA-6.4.3-full.rar’ and you’ll find a NRG file. This is a CD image that you’ll need to either burn to a CD or extract to a folder using a tool such as ISOBuster. Once extracted, go into the following folder ‘/REFERENZ/INSTALL/’, right-click on ‘INSTPROG.exe’ and select ‘Properties’, click on the Compatibility tab and change the dropdown to Windows XP SP3 as the Compatibility Mode, also tick ‘Run As Administrator’, then click ‘Ok’, then double-click the file to run the installation. Select ‘English’ as the language and click ‘Next’. Select ‘Next’ until asked for ‘Configuration’, scroll to ‘BMW Group Rectification Programs UK’, click ‘Next’. Tick the option ‘Complete’ for all of the options shown. Select ‘Next’ and allow the installation to start. After a minute or so, installation will complete, close the Window. The BMW INPA software can also be downloaded from here. 4. Verify environment variables Go into Control Panel -> System -> Advanced System Settings. Select ‘Environment Variables’ and then verify that the System Variables ‘TMP’ and ‘TEMP’ both contain the path ‘C:EDIABASBin’ within the ‘Value’ string – for instance “C:WindowsTemp;C:EDIABASBin”. 5. Prepare Installation Files Extract the contents of the downloaded file ‘INPA_502_Updated.rar’. You’ll use the contents of this archive during the next three steps. 6. Install BMW Tools From the above extracted file set, find the file ‘Step 1_ Install BMW Tools.exe’, right-click on it and select ‘Properties’. Click on the Compatibility tab and change the dropdown to Windows XP SP3 as the Compatibility Mode, also tick ‘Run As Administrator’, then click ‘Ok’ Double-click on the above file to start the installation. Set the Destination Path C:BMW Tools (Don’t change this path) -> ‘Install’ -> ‘OK’. Select ‘English’ -> ‘Continue’ -> ‘Continue’. Select ‘C:’ -> ‘Continue’. Select ‘Skip’ -> ‘Next’ Accept the defaults for programs to update, then click ‘Next’. Select ‘Com1′, ‘OBD’ and ‘USB to Serial Adapter’ -> ‘Continue’ -> ‘Continue’. The installation will begin and complete. 7. Install INPA/EDIABAS 6.4.7 and 5.0.2 From the above extracted file set, double-click the file ‘Step 2_ Install INPA.exe’.… Continue Reading
Original Autel AutoLink AL619 OBDII & CAN ABS and SRS scanner supports multi-language, including German, French, Spanish, Portuguese, Polish, Italian, Dutch and Russian. The default language is English. But you are able to change the language you want if you register at Autel official website and provide your device SN. If the Autel AL619 scan tool shows it’s the French version, but it only shows “Control” and “Play” on the screen without giving any error massage. No matter how it was connected by OBD or USB, Autel AutoLink scanner didn’t work at that time. Here are some screenshots when updating Audi software: Autel AutoLink AL619 scanner can be upgraded into the French version so the vehicle software must be the French version. If the language of the scanner is the still English version, the auto diagnostic tool cannot be seen. When you set the AL169 scanner main unit into the French version, you should set the software into the French version after the machine restarts to enter the software equipment. That is, the software for diagnosing vehicle and the machine language should be the same, i.e French, so that the software for being used for the vehicle can be seen on the computer. In short, after you update the French software, you should also setup your Autel AL619 device language to be French.
Linde Canbox USB Diagnostic Tool, newest version is V2013. It is reliable, high speed, high performance tool, and it supports multi-language: English/ Hungarian/ Dutch/ Danish/ Spanish/ Italian/ German/ Dutch/ Norwegian/ Polish/ Russian/ French/ Czech/ Swedish/ Turkish. It comes with a Pathfinder software, like following… Continue Reading
BMW engineering and development diagnostic software can project powerful functions for both old and new BMW series, like E39, E60, E65 etc, CANBUS modelE60, E65 and old vehicle models, like E39. Following are some of the most significant functions of INPA EDIABAS: Basic diagnostic (read/clear fault codes) Read parameters of real time Reads the content of the computer memory Coding of the ECU Activation of the actuations Conformity check codes VIN and mileage car in various computer memory; Identify different computer systems … OBD Tool here offers BMW INPA EDIABAS (full package including: E-sys, WinKFP, NCS-Expert etc diagnostic software.) free download software. Computer configuration: Windows XP SP2/SP3 O/S Hard disk: at least 20 GB free space 512 MB RAM Free download INPA full iso (326MB) BMW INPA Ediabas bit 64 BMW INPA 5.0 diagnostic software BMW INPA 5.02 and Ediabas V6.47 (Crack) INPA V5.06 torrent free download (2.59 GB) BMW Ediabas V10.9 software full download Relate Hot BMW Scanner products: 1. INPA K+DCAN Full OBD2 Diagnostic Tool with FT232RL Chip for BMW 2. Unlock… Continue Reading
OBD Tool technicians have extracted Volvo Vida Dice 2014A software today and shared it for free download here. This software version features an Alcohol file that makes it easy to open ISO files. Note: This software we provide is a BT file and you… Continue Reading
Eobdtool.co.uk has newly launched VXSCAN S1OBDII/EOBD mini hand-held code reader to diagnose your vehicle. VXSCAN S1scanner supports all OBDII/EOBD compliant vehicles to enable car owner or technicians to accurately diagnose engine problems. Language: English, Spanish, French Vehicle model support: Works on all 1996 and later OBDII compliant US, European and Asian vehicles Vehicle protocol: CAN, K-Line ISO9141, KWP 5BAUD INIT, KWP ADDR INT, KWP FAST INIT, J1850 PWM, J1850 VPW Update: Online (Click “Vehicle Info” tab to check current software version) One year warranty VXSCAN S1 EOBD OBDII DIY Code Scanner Feature and Function: 1. Easily determines the cause of the “Check Engine Light (MIL)” 2. Retrieve generic (P0, P2, P3, and U0) and manufacturer specific (P1, P3, and U1) codes 3.Turn off Check Engine Light (MIL), clear codes and reset monitors 1. View freeze frame data 2. Display live data & DTC definitions 3. Display I/M readiness status 4. Identify pending codes 5. Retrieve vehicle information (VIN) Original VXSCAN S1 EOBD OBDII scan tool User Manual: http://www.eobdtool.co.uk/upload/pro/vxscan-user-manual.rar
Key Pro M8 most powerful Car Key Programmer and Locksmith Diagnostic tool come with 800 tokens with the machine. Not all car models key programming need tokens, if your car needs token, the screen will promt you how many tokens are needed. After 800 tokens are used up, you need charge your device with new token. You can choose how many tokens need: 250 Tokens for The Key Pro M8 Auto Key Programmer 100 Tokens for The Key Pro M8 Auto Key Programmer Here is Key Pro M8 Update Tokens Manual 1. Send us the M8 serial number, within 24 hours, we will notify you when you can update token. 2. connect your computer to network, and then use the USB cable to connect the M8 and the computer. 3. Plug the power supply cable into the M8, and then turn on M8 till the following window appears. 4. The window “Found New Hardware Wizard” popup, tick off “Install from a list or specific location (Advanced)”, and then click “Next”. 5. tick off “Search for the best driver in these locations” and “Include this location in the search”, and then click “Browse” to choose the installation location. 6. After click “Browse”, choose the driver location: browse for Folder-Desktop-The key pro (M8) driver-OK. 7. click “Continue Anyway”. 8. please wait while the wizard installs the software… 9. click “Finish” and the wizard complete installing the software for the key Pro M8. 10. stay in the following window even some change happens during the process. 11. click “M8 Tool.exe” to show as below, “Serial Number” will be automatically indentified, input M8 6-digit password and click “Login”. 12. in the drop-down list of “select TOKEN quantity” choose the TOKEN quantify you bought from the dealer, double click “Update TOKEN”. 13. a window popup reading “Update TOKEN finish!” 14. wait until you see the Current TOKEN number already includes that you bought, and click “Finish”. You can Download and Save the Key Pro M8 Auto Key Programmer Tokens Update Manual.PDF Here is video on How to Add The Key Pro M8 Tokens · Key Pro M8 Manual · Key Pro M8 Tokens