OBDSTAR X300 DP Plus A B C Package Function List

obdstar X300 DP plus A B C package are the same in the hardware, but different in the software functions configuration. The main functions are Immobilizer key programming/ Pin code reading, cluster calibration, special functions, OBDII diagnosis etc.

 

Table: obdstar X300 DP plus A package Vs B package Vs C package:

Functions Regional market Software Configuration X300 DP plus Remark
A package B package C package
Immobilizer / Remote programming European cars VW/Audi

/Skoda

/Seat (Standard)

Yes Yes Yes
VW/Audi

/Skoda

/Seat (Advanced)

Yes Yes Yes add NEC 24C64

2014-key programming.

BMW

(Standard)

BMW (Advanced) Yes Yes Yes Add FEM/BDC

key programming,

ISN code reading etc.

Volvo Yes Yes Yes
The other European cars Yes Yes Yes
Asian cars Hyundai /Kia (Standard)
Hyundai /Kia (Advanced) Yes Yes Yes Add 47/8A/46 smart key

pin code reading

Toyota /Lexus (Standard)
Toyota /Lexus (Advanced) Yes Yes Yes For Middle east cars,

it adds H chip

all keys lost (Immo box reset)

The Asian cars Yes Yes Yes
North American cars Ford(Standard)
Ford (Advanced) Yes Yes Yes Add Ford after 2015 key programming

functions, I.E: Mobdeo,Edge,Taurus,Escort,

EVEREST,

Explorer,F-150 SVT Raptor,Mustang,

Lincoln MKZ, MKC and Continental 2015 – etc.

GM(Standard)
GM(Advanced) Yes Yes Yes
The other American & Chinese cars Yes Yes Yes Can perform BMC

pin code reaing on these cars: -2017 Lacrosse,Lacrosse,

Trax,Envision, GL8,MALIBU,AVEO,Excelle before 2015,Cruze etc.

Cluster Calibration All cars cluster calibration Yes Yes
4-system diagnosis Engine, Transmission,

ABS, airbag reset

OBDII Diagnosis Multi-system diagnosis Yes Multi-system diagnosis
Special function Oil service reset Yes Reset the Oil Service Light on
Manual remote setting Some cars only supports

manual remote setting.

ABS bleeding Yes After replacing the ABS pump and related components.
Battery matching Yes After the battery is changed,

you need to match the battery.

ECU programming Yes
The car with EPB replace brake pads Yes Electronic Parking Brake release
Throttle programming Yes Used to clear the learning value after cleaning the throttle, otherwise, it will cause high idle speed.
Airbag reset Yes Used to clear airbag ECU collision data after a vehicle collision, otherwise, the ECU cannot be reused
TPMS reset Yes Used for reset after tire pressure alarm
Steering angle reset Yes Replacement of data lost after steering angle change or power off
OBDII Engine Yes Used to diagnose the car with OBD protocol.
DPF Regeneration Yes Diesel Particulate Filter Operational
Injector coding Yes Used to match and code the injector after replacement
Suspension match Yes Used to match and set the suspension after adjusting.
Gear learning Yes Used to learn the crankshaft position sensor after power off (only the domestic vehicle equipped with the Delphi system has this function)
CVT learning Yes Used to reset the learning value after maintenance of CVT transmission
EEPROM Yes Read and write the EEPROM; read 8-pin IC chip password and reset some models anti-theft
Key Renew Yes Renew the used keys to solve the problem that used keys cannot be matched to other models
Steering angle repair Yes Used for the repair of lost data of vehicle steering angle sensor
ECU Clone Yes Used for copying the program when replacing the new/second-hand computer.
Switch activation Yes
Hardware P001 Programmer unit Yes Yes Yes
C001 circuit board Yes Yes Yes
C002 circuit board Yes Yes Yes
W001 data cable Yes Yes Yes
W002 data cable Yes Yes Yes
W003 data cable Yes Yes Yes
Toyota smart key emulators Yes Yes Yes
Remote Tester Yes Yes Yes
Anti-theft Induction coil Yes Yes Yes Used to test if the coil can send out the transmit signal.

 

Details:

  1. obdstar X300 DP plus add wiring harness of ECU reading by OBD (for ECU cloning and switch activation)

 

A.obdstar X300 DP plus ECU clone:

ECU cloning means copy ECU, that is the OBDSTAR X300 DP Plus copies the data from the original car ECU, then write it into another same ECU hardware, so that it can achieve the same function as the original ECU.

When you want to change the new ECU or the second ECU, if you use X300 DP Plus to clone via OBD, you won’t need to go to the 4s store to do the online programming or dismantle ECU to weld, read & write.

ECU clone Pros :

No need to go to 4S shop, convenient, fast and save money.

Simplify the operating steps, even the amateur can also operate.

No need to dismantle and weld the ECU to read & write, it is zero risk to clone ECU via OBD with the X300 DP Plus.

B.Switch activation function:

Nowadays, many car models’ accessory power supply of the dashboard or audio equipment needs to be activated to enter the boot status through the related module CAN.

However, when the car technician maintains the dashboard/audio equipment, the main unit is out of the CANBUS network so it maybe won’t boot. X300 DP plus” switch activation function” can emulate the CANBUS communication to active the power supply of dashboard / Audio so that it can enter the boot status, then it will test and verify the dashboard and the Audio, also the technician can save money avoiding to purchase many the boot platform and cables of kinds of car models.

 

  1. P001 Programmer unit integrates  EEPROM adapter + RFID adapter+ Key Renew adapter

  1. Add the clip of reading SOP 8PIN EEPROM
  2. C001/C002 circuit board to read and write chip data with welding

image 1: C001 circuit board is compatible with old NO. 3 and 4 circuit boards, applying to EEPROM chip dismantling and reading, Tianjin FAW and VIZHI immobilizer coil initialization and other functions.

Image 2: C002 circuit board is connected by W001, W002 or W003 without welding the chip.

  1. IMMO induction coil to detect the key induction coil failure of the vehicle.

 

  1. Add Toyota Simulated Smart Key for free

Simulated key 1 applies to the vehicle with 94/D4 type of smart key;
Simulated key 2 applies to the vehicle with 98 type of smart key;
Simulated key 3 applies to the vehicle with 88/A8 type of smart key;
Simulated key 4 applies to the vehicle with A9 type of smart key;

 

  1. Adds the “Help” function including the testable car models, update notice, special features, help instruction, wiring diagram etc.

Testable car models: The user can read the testable car models and year.

Update notice: The user can read all of the update content.

Features: The user can read all of the special features and the functions that only X300 DP Plus supports.

Help instruction: Built-in the guide and instruction for each car model or function.

Wiring diagram: Built-in ECU wiring diagram, more intuitive and convenient.

For example:

 

www.eobdtool.co.uk

eobdtool.co.uk